Just How to Set up a Bathtub Yourself
Just How to Set up a Bathtub Yourself
Blog Article
The writer is making a few good points about Installing A Bathtub as a whole in this great article which follows.
Setting up a tub isn't precisely rocket science, however it does call for strong plumbing, woodworking, and sometimes, tiling abilities. Changing an old tub with a brand-new one is likewise a moderately challenging task. If the old tub is readily available, the job can relocate speedily; if you have to open a wall to eliminate the old bathtub and also position the new bathtub, the task is a lot harder. In either instance, the job is within a residence handyman's abilities, although you will certainly require an assistant to move out the old bathtub and set in the new one. Make sure you have actually certified on your own for the task and fit trying it. As opposed to employing a specialist to take control of a halfway-completed task, it is far better to take into consideration using one prior to you start. Possibilities are you may require a specialist plumber to make tube links.
This write-up will certainly assist you set up a new tub in your bathroom if you have already bought a new bathtub and also do not require to alter the arrangement of your previous water pipelines.
Your tools and material list must comprise the following:
Planning for the Setup
Firstly, the sustaining frame supplied with the bath needs to be fitted (if needed) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to make sure that if the faucet comes with a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the faucets device to prevent pressure on the tub.
Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be suited its final setting.
Removing Old Touches
If you need to change old taps with new ones as a part of your installment, after that the first thing you ought to do is separate the water supply. After doing so, switch on the faucets to drain pipes any water staying in the system. The procedure of removing the existing faucets can be fairly problematic as a result of the restricted gain access to that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a towel ready for the remaining water that will come from the pipes. Once the supply pipes have actually been gotten rid of, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from transforming throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing compound.
Prior to going on to fit the brand-new faucets, compare the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Making use of both wood boards under its feet, position the bath tub in the called for placement. The wood boards are helpful in evenly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 small points.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the tub up until the spirit level reads level.
To install taps, fit all-time low of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Switch on the supply of water and examine all joints as well as new pipework for leaks and tighten them if necessary. Fill the bath tub as well as likewise inspect the overflow outlet and the normal electrical outlet for leaks.
Finally, deal with the bathroom paneling as described in the supplier's user's manual. Tiling and also securing around the bath tub needs to wait till the bath tub has actually been utilized a minimum of once as this will settle it into its last position.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to prevent damages to the string. One end of the connector fits on the plastic tail of the tap as well as the other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, then you will require minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the mounting opening in the bath/basin making certain that the washers are in area in between the tap and also the sink. Protect the tap in place with the maker offered backnut. Once the faucet is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical tap ports. The previous kind ought to be connected to the faucet ends first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture a rigid seal, creating the water to penetrate the wall in between the bath as well as the tiling, leading to issues with dampness as well as feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures and installations. They are sold in tubes as well as cartridges, and also are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water prior to sealing, to enable the activity experienced when the tub remains in use. The sealer can crack rather very early if you do not consider this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise easily offered on the marketplace. It is suggested to fit the floor tiles utilizing water-resistant or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very interested in How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I'm hoping you liked the new blog posting. Those who enjoyed our post if you please do not forget to pass it around. Thanks a lot for your time. Please come by our blog back soon.
Get Offer
Report this page